tilt steering column write up

------------------------------
Date:  Mon, 26 May 1997 15:46:41 -0400 (EDT)
From: Chrisharon@aol.com
Subject: Tilt steering column fix

   This is what I did to fix a loose steering column (at the pivot point for
the tilt) on a '78 Cherokee.  Hopefully this will be of help to others with the
same problem.

   Special equipment required: Universal puller set (this is what I used) or
perhaps a regular steering wheel puller.

1) Disconnect battery

2) Remove horn button

3) Remove large nut and washer on steering shaft.

4) Remove the 3 screws in plastic insulator for horn button.  Remove as an
    assembly: plastic insulator, metal dish, and metal plate.

5) Scribe an alignment mark from steering shaft to steering wheel so you can
    reassemble with the wheel in the correct orientation.

6) Use steering wheel puller and remove steering wheel.

7) Remove plastic anti-theft plate.

8) Install steering wheel puller over steering shaft, (be careful not to
    crush the plastic cancelling cam (it's also where the horn circuit comes through)
    and tighten shaft nut and washer (that you already took off) over puller.

9) Use two bolts and nuts and install with bolt through puller, with nut on the
    bottom so you can use the bolts to push on (compress) the steering lock plate. 

10) Remove clip from steering shaft.  NOTE: My Jeep technical service
manual says NOT to re-use this clip.  I've had mine out twice and have re-used
it both times, the decision is yours.

11) Decompress lock plate.

12) Remove steering nut, washer, and steering wheel puller.

13) Remove lock plate.

14) Remove cancelling cam, and spring.

15) Remove 4 bolts securing support brace to steering column under dash.

16) Remove 2 bolts securing support to dashboard.

17) Remove column support brace.

18) Disconnect wiring coming from under the column, remove plug from it's
holder and leave hanging.

19) Remove screw holding turn signal switch handle to switch assembly.

20) Remove 3 screws holding turn signal switch (you'll have to turn the
switch to get to all 3 screws).

21) Remove turn signal switch, you should be able to feed the wired up
through the column to give you enough slack to do this.  You can get a little more
slack by lifting the plastic cover (under the column) over the wires.

22) I did this step, but I don't know if it's required or not.  Put key in
ignition lock.  Turn to locked position.  You should be able to see a small bar coming out
of the end of the lock.  Just to the right of that is a small slot, inert a
small screwdriver into the slot and push. Remove key lock assembly.

23) Use a pair of long nose pliers, and remove spring clips from shift
indicator on top of steering column.

29) Remove shift indicator.

30) Remove 2 screws on top of column, shift indicator light, and metal cover.

31) Remove tilt handle. 

32) Remove upper column housing (Painted housing where ignition key goes). 

33) Reinstall tilt handle. 

34) Tilt steering wheel in full up position. 

35) Their's a round metal piece towards the bottom with a square hole in it.
Using a screwdriver, push in and turn about 1/4 turn until this piece comes out. 

36) If it didn't come out with the metal cup in the above step, remove spring. 

37) Using a puller tool (I made my own) remove pivot pins.  This
is what I did:
          Get a 1/2" open end wrench, the screw that came out of the turn signal
           handle, a washer & a nut that will fit the screw.  Install nut onto screw until
           it bottoms out, and install washer against nut.  Put the 1/2" wrench over the
           pivot pin (make sure the pin will go through the wrench ends when it's pulled
           or you'll strip something out).  Install the screw into the pin, and tighten the
           nut until the pin is loose.  This is what *I* did, something else,may work
           better for you.

38) Hold the housing on the column, pull on the title handle, and remove the housing.

   That's all the disassembly there is.  There should be 4 loose bolts after
that. They're not regular bolts, they look almost like a torque bit.  I used a
12pt 1/4" drive socket (don't remember what size).  Remove one bolt at a time,
clean it, apply locktight, and reinstall.  Then reverse the disassembly
instructions and you're finished.  The pivot pins just press back in, not a
problem.

   Hopefully I didn't leave out too many steps.  If anybody uses this info,
please let me know how accurate or helpful this was, and feel free to add to
this, I just went by memory here.  I don't know what all years will be exactly
the same.  This how-to could also be used for lock replacement, just stop after
step 22.

Chris Enos ('78 Cherokee, TH-400, Q-Track 16% OD P/T, 3.55, 33")

SJ 1962 - 1991
SJ tech - repair tips
SJ rigs - photos
the 1996 snowstorm

since September 24, 1998.
XJ 1984-2001
XJ tech - repair tips
XJ rigs - photos
john's fotos
2011

fotos: 2010
fotos: 2009
fotos: 2008
fotos: 2007

FotoMeister.us

best of fotomeister

WJ 1999-2004
WJ tech
WJ rigs
Google
SEARCH TOOL:
wagoneers.com
fotomeister.us
johnmeister.com
ENTIRE WEB

WILLYS
  /   JEEPS
john's Jeep History
AMSOIL

call 1-800-956-5695,
CUSTOMER NUMBER is 283461
FSJ Filters
XJ Filters

DieselBenz

DieselBenz TECH
DieselBenz CARS

JohnMeister.com
DIESELS
SHOP from wagoneers.com - THANK YOU: in Association with Amazon.com
Click for Snohomish, Washington Forecast

Diesel project:
2003 VW Jetta GLS Wagon TDI


john's vehicles
BIBLE info
BIBLE Summary Book
Computer Science
LINUX
XP vs. Linux

JohnMeister.com
tmp files
Bible Summary draft version
email john at wagoneers.com


Trust Jesus.
Jesus Christ is Lord.

summary: Passion Week prophecies - © 2010

thank you for using
customer number 283461

wagoneers.com: in Association with Amazon.com
shopping amazon from here,
supports this site, THANK YOU!


some recommendations

It is about FREEDOM!
mac and jack - 2010

summary page: Bible - © 2010
X Y